Topeak's FlashStand is a super work/display stand that folds up to become extremely portable as well! This affordable two-footed wonder supports your bike at the bottom bracket and down tube and raises the rear wheel with two adjustable-height feet. Take it along in the trunk of your car to dial-in your ride before your next adventure!
Park Tool's 106-AC easily adapts the #106 Work Tray or PTH-1 Paper Towel Holder to fit 35mm-37mm upright tubes on PCS-9 Repair Stands, as well as 2003 and newer PCS-1, PCS-4, PCS-4-1, PCS-4-2 Repair Stands.
The PCS-EXT is an extension for the older pre-2001 repair stands. The kit includes a quick-release collar and extension tube to raise the working height of the stand. The PCS-EXT is required for use of the 106-AC (sold separately).
$9.14 - $25.08
Everyone wears out their Park Tool work stand clamp covers at some point. Find replacement covers for yours here. Each cover is constructed of soft, durable composite rubber. See below to determine which covers fit your Park Tool stand clamp: - 1002: fits 100-3X and 100-5X extreme range clamps - 1185: fits clamps on the repair stands PCS-9, PCS-10, PCS-11, and PCS-12 - 1259: fits 100-4X, 100-6X, 100-7X, and 100-15X clamps - 1960: fits 100-3D, 100-5D, and 100-25D Professional Micro Adjust Repair Stand Clamps - 468B: fits clamps with double cable reliefs, including 100-3C, 100-5C, 100-8C, 100-8Y, and 100-9C clamps - 467B: fits clamps with single cable relief, including PRS-2 through PRS-8 (for older-style clamps, non-current) - 468G: fits PCS-1 and PCS-2 clamps with double cable reliefs (clamp models: 100-1C, 100-1CA, and 100-2C) - 467G: fits PCS-1 and PCS-2 clamps with single cable relief (for older PCS-series stands only; not for current model stands) - 466: Rubber Replacement Clamp Cover Set (fits older clamps with plastic-dipped jaws)
Includes a new tray/motor shroud, USB ports and oversized buttons to upgrade a Park Tool PRS-33 or PRS-33 AOK into the PRS-33.2 version controls and electronics.
A 6-inch (15cm) extension that easily mounts to the main beam of any PRS-22 or PRS-22.2 to accommodate longer wheelbase bikes with bottom bracket-to-front axle lengths over 28.75 inches, including CX, gravel and enduro style bikes.
The Travel and Storage Bag is a heavyweight nylon bag with a shoulder strap. This bag is designed for transporting and storing your Park Professional Race Stand. It makes travel easy and convenient, while also protecting your stand.
For wheels to perform properly, it's important that the rims be centered over the hubs. To check this, and to make precision adjustments, Park's Wheel Alignment Gauge (also called a dishing tool) is a must. It allows you to easily check centering on road, mountain and BMX wheels from 16 to 29 inches in diameter. It works with any hub width and its innovative design even allows it to be accurately used with the tire still on the wheel. The Wheel Alignment Gauge is a necessity for every wheelbuilder.
Keep your most-needed bike repair tools and supplies close at hand with Park's Work Tray. It easily installs on your Park PRS-15, PRS-10, or PRS-11 Repair Stand (sold separately). And it features 2 separate compartments, a lube holder, a tool/towel bar, a tab system that holds plastic grocery bags and 2 receiver pods for extra accessories.
Park's Paper-Towel Holder is an accessory for Park's Professional Race Stand (sold separately). It attaches easily and holds a standard roll of paper towels. It also works great for hanging clothes, wheels and tires.
At nearly 20% lighter than our (already) lightweight stand collection, the Ultralight takes no performance shortcuts to achieve its feathery 10.6lb (4.8kg) total weight. Despite a slender scale reading it still possess the same durability and stability of our other stands. With the 360° rotating Slide-Lock clamp and a 54? (137cm) wide base with rubber-coated end caps, confidence in the security of your bike is never in question. And when the service day is done, it folds in to a space-saving unit for storage or travel. Look to our Tool Tray and Pro Truing Station upgrades to create the optimal home bike maintenance setup.
Permanently and securely attach your Park Tool Repair Stand (sold separately) to the floor of your shop with Park's Floor Mounting Plate. Made with an 8" square of steel, it attaches to the stand with four bolts, which are included.
The Travel and Storage Bag is a heavyweight nylon bag with a shoulder strap. This bag is designed for transporting and storing your Park Team Race Stand. It makes travel easy and convenient, while also protecting your stand.
A versatile and convenient way to keep tools, supplies and technology at arms length on a PRS-33 Power Lift Repair Stand. The PRS-33TT solidly mounts directly to either side of the stand’s upright at any height. - 19 tool holding holes, slots and small trays in a variety of shapes and sizes - 14-inch (35cm) magnetic tool bar - Integrated mounting holes for PTH-1 Paper Towel Holder - Phone/tablet/clipboard holder - Pen and pencil holders - Adjustable utility hook to hang wheels, parts and scales - Height adjustable - Can be installed on a fully assembled stand
The RPP-1 offers simple but effective protection for your service area. This 32" tall pad prevents damage to bikes caused by being leaned against or knocked over onto your Park Tool professional repair stand. Covered with an attractive Park Tool blue vinyl finish for easy wiping off of dirt and grease. - Compatible with Park Tool Shop Repair Stands with a 2" diameter lower post, including all generations of PRS-2 and PRS-3 - Easily removed and installed with hook-and-loop material
Bontrager's Universal Repair Stand Adapter safely holds your Trek Madone road bicycle in a traditional workstand (sold separately). It securely holds your bike in any clamp-style or screw-type repair stand. This universal adapter has replaceable inserts to accommodate different mast caps and adapters for the 2008 and 2010 Madones.
A pro level workstand with a built-in digital weight scale. Stable tripod design folds down small for travel or use at the races. Additional clamp lever for tightening / releasing the clamp with ease. Clamp Head Non-marring rubber jaws 360° rotation Digital weight scale Clamp Height 122 cm to 183 cm (48” - 72”) Clamp Opening 1.9 cm to 4.5 cm (0.75” - 1.8”)
Mount the THS-1 Trailhead Workstation (sold separately) directly to this rigid steel post. Features: - 2-inch (5cm) square post plated then powder coated for long outdoor life - Includes THS-1 mounting fasteners - 6-inch (15cm) square base with holes to mount directly into hard surface or to Park Tool #130 Base Plate (fasteners not included) - Height: 62.25-inch (158cm) positioning cradle arms at 50.5-inch (128cm)
If your bike has a hollow bottom bracket, the Pro Bottom Bracket stand makes it easy and convenient to do maintenance work. This stands folds up for easy storage when not in use. - Compatible with Hollowtech 2 bottom brackets - Coated alloy - Anti-slip base
Being a "shade tree mechanic" doesn't mean you should lean your bike against a tree. You paid hard-earned money for your family's bike collection and we've got a budget-conscious, yet feature-loaded bike repair stand that's perfect for the home bike mechanic. The price-point leading 360-degree rotating clamp can position your bike optimally for any work you're planning. Plus, the Recreational Stand leverages a 52-inch (132cm) wide base with rubber-coated end caps for fantastic stability on any surface. And when the service day is done, it folds into a space-saving unit for storage. Add a Tool Tray, Bottle Opener and a Pro Truing Stand for the complete at-home bike shop. - Seatpost clamp features Spinner Knob for quick closure and precision clamping pressure - 360-degree rotating clamp design provides easy access to any part of your bicycle - Fixed clamp height at 55-inch (139cm) - Rubber-coated clamp secures and protects expensive components and beautifully painted frames - Clamp opening up to 1.9-inch (4.8cm) accommodates even the largest diameter frame tubes - Powder-coated steel construction is corrosion resistant and incredibly durable - Stiff 52-inch (132cm) base and rubber-coated end caps create ultimate stability even on uneven surfaces - Total load capacity of 60lbs (27.2kg) accommodates service on most road, mountain bikes, fitness bikes, and electric bikes - Portable and compact construction creates a remarkably small folded footprint of 10 x 4 x 55-inches (25.4 x 10.2 x 139.7cm) - Optional Travel Bag available - At 13.8lbs (6.3kg), moving in and out of storage is no problem - No assembly required - 3-year Warranty
Park Tool's 130 Repair Stand Base is designed for the PRS-3, PRS-3OSLB, PRS-3 OS-1, PRS-3 OS-2 and the PRS-23 LB Repair Stands (each sold separately). • 22-1/2" x 22-1/2" x 7/16" (57cm x 57cm by 1.1cm) steel plate • Approximately 68 lbs (31k) • Black painted
Page 1 of 1